MARTINDALE MM84 Guia do Utilizador descarregar pdf (Página 18)

4kV Flash Tester

Metrohm

E3640

Power Requirement:

115/230 Volts ±15% 50/60Hz 40VA

Fuses:

230V - 5x20mm 0.25A, HBC, Type F

115V - 5x20mm 0.5A, HBC, Type F

Output Voltage Range:

0 - 2.2, 0 - 4.2kV 50/60Hz

Output Voltage Accuracy:

± 2% of reading ± 1 digit

Leakage Current: 0 - 5 mA

(nominal) 50/60Hz in 10μA steps

Leakage Current Accuracy:

±2% of reading ± 1 digit

Trip Level Range: 0 to 3mA 50/60Hz

Setting Accuracy:

±5% of full range

Trip Response Leakage: Will trip

for fault duration >5mS but not for

<100μS

Breakdown: Will trip for fast

transients of 30μS and above

Complies with: EMC: To BS EN

50081-1 and BS EN 50082-2

Safety & Flash Test: BS EN 61010-1

Dimensions: 330 x 263 x 144mm

Weight: 4000g approx

Includes: flash gun, earth lead,

mains power lead and manual

This digital flash tester is a portable mains operated

instrument, capable of operating from either 115V or

230V supplies at 50/60Hz. It can apply up to 4kV AC

and displays both output voltage and leakage current

on the twin 3½ digit LCD’s.

The fail lamp illuminates and the buzzer sounds in the

chosen modes:

Trip - will trip when pre-determined current is

exceeded;

Breakdown - fast transients can trigger the trip;

Burn - where the trip function is by-passed and the

fault current flows continuously to expose the fault;

Hold shows the breakdown voltage and the leakage

current.

5kV Insulation Tester

E3511

Insulation Resistance Range:

100kΩ to 100GΩ

Insulation Range Accuracy:

±1.5% of scale length

Insulation Range Temperature

Coefficient: <0.04% of scale

length/°C

Voltage Range:

1000 volts AC or DC

Voltage Range Accuracy:

±1.5% of scale length

Test Voltages:

500V, 1kV, 2.5kV, 5kV DC

Test Voltage Accuracy:

±5% at 10MΩ

Break Point Current: 0.5mA

nominal

Short Circuit Current: 1.2mA

nominal

Ripple Voltage: <10V peak to peak

(R<10MΩ)

Housing: yellow ABS, black & clear

polycarbonate

Dimension: 330 x 263 x 144mm

Weight: 4200g approx (incl batteries)

Includes: 2m test leads & crop

clips, accessory bag

Having both battery and mains operation and four

selectable DC test voltages (500V, 1kV, 2.5kV & 5kV),

this tester measures insulation resistance from 100kΩ

to 100GΩ. The large, clear analogue scale also

displays AC or DC voltage up to 1000V. Latching test

switch allows hands free testing.

With full over-voltage and over-current protection for

measurements and 4-16 hours operation from re-

chargeable NiMH batteries, the E3511 comes

complete in a rugged carry case. Standard

accessories include locking 2m test leads with prods

and clips.

METE3640 4kV flash tester £975.00

TC2D calibration £72.00

METE3511 5kV insulation tester £1175.00

TC2D calibration £72.00

METDFK0075/A replacement 2m test leads £140.00

METDFK0075/C optional 10m test leads £175.00

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 67 68

Comentários a estes Manuais

Sem comentários

MARTINDALE MM84 Guia do Utilizador Página 18

Comentários a estes Manuais

Manuais e produtos relacionados com Multímetros MARTINDALE MM84